Boonton 4530 Peak Power Meter User Manual Manual de usuario descargar pdf (Pagina 132)

4-58

Chapter 4 Boonton Electronics

Remote Operation 4530 Series RF Power Meter

MEMory:SYS[1 | 2 | 3 | 4]:LOAD recall stored instrument setup from setup memory location 1 thru 4.

MEMory:SYS[1 | 2 | 3 | 4]:STORe store instrument setup in setup memory location 1 thru 4.

MEMory:FDOFfset:TBLA:DATA <asc> set/return data array for frequency-dependent offset table A

MEMory:FDOFfset:TBLB:DATA <asc> set/return data array for frequency-dependent offset table B

OUTPut:{INTernal | EXTernal}:SIGNal <asc> set/return selected calibrator output state, <asc> = OFF, ON

OUTPut:{INTernal | EXTernal}:LEVel <n> set/return selected calibrator output level, <n> = -60.0 to +20.0 dBm

OUTPut:EXTernal:MODulation <asc> set/return external calibrator modulation, <asc> = CW, PULSE

OUTPut:EXTernal:PULse:PERiod <asc> set/return external calibrator pulse period, <asc> = .1, 1, 10 ms

OUTPut:EXTernal:PULse:DCYC <asc> set/return external calibrator pulse duty cycle, <asc> = 10 to 90 %

OUTPut:EXTernal:PULse:SOURce <asc> set/return external calibrator modulation source, <asc> = INT, EXT

OUTPut:RECOrder:SIGNal <asc> set/return Recorder Output state, <asc> = OFF, ON

OUTPut:RECOrder:SOURce <asc> set/return Recorder Output source, <asc> = CH1, CH2

OUTPut:RECOrder:MEAS <asc> set/return Recorder function, <asc> = AUTO, MANUAL, ALARM

OUTPut:RECOrder:POLarity <asc> set/return Recorder Output polarity, <asc> = UNIPOLAR, BIPOLAR

OUTPut:RECOrder:MIN <n> set/return Recorder Output dnscale level, <n> = -100.00 to +100.00 dBm

OUTPut:RECOrder:MAX <n> set/return Recorder Output fullscale level, <n> = -100.00 to +100.00 dBm

OUTPut:RECOrder:FORCE <n> set/return Recorder Output level directly, <n> = -10.0 to +10.0 volts

OUTPut:RECOrder:CALibration:SLOPe <n> set/return Recorder Output slope adjustment, <n> = -10.00 to +10.00%

OUTPut:RECOrder:CALibration:ZERO <n> set/return Recorder Output zero adjustment, <n> = -1.000 to +1.000 volts

OUTPut:RECOrder:CALibration:SAVE save Recorder Output adjustments to non-volatile calibration memory

READ[1 | 2]:CW:POWer? perform measurement, return new average reading in power units

READ[1 | 2]:CW:VOLTage? perform measurement, return new average reading in voltage units

READ[1 | 2]:MARKer[1 | 2]:POWer? perform measurement, return reading at the specified marker

READ[1 | 2]:ARRay:MARKer:POWer? perform measurement, return readings at both markers

READ[1 | 2]:ARRay:MARKer:PERcent? perform measurement, return statistical percent at both markers

READ[1 | 2]:ARRay:CW:POWer? perform measurement, return array of power readings

READ[1 | 2]:ARRay:CW:VOLTage? perform measurement, return array of voltage readings

READ[1 | 2]:ARRay:PULse:POWer? perform measurement, return array of marker measurements

READ[1 | 2]:ARRay:AMEAsure:TIMe? perform measurement, return array of automatic pulse timing measrmnts

READ[1 | 2]:ARRay:AMEAsure:POWer? perform measurement, return array of automatic pulse pwr measurmnts

SENSe[1 | 2]:AVERage <n> set/return trace averaging count, <n> = 1 to 4096

SENSe[1 | 2]:BANDwidth <asc> set/return sensor video bandwidth, <asc> = LOW, HIGH

SENSe[1 | 2]:CORRection:OFFset <n> set/return sensor offset value in dB, <n> = -100.00 to +100.00 dB

SENSe[1 | 2]:CORRection:FREQuency <n> set/return sensor measurement frequency in GHz, <n> = 0.001 to 110.00

SENSe[1 | 2]:CORRection:CALFactor <n> set/return sensor cal factor in dB, <n> = -3.00 to +3.00 dB

SENSe[1 | 2]:CORRection:FDOFfset <asc> set/return current freq dependent offset table, <asc> = OFF, TBLA, TBLB

SENSe[1 | 2]:CORRection:TEMPComp <asc> set/return peak sensor temperature compensation state, <asc> = OFF, ON

SENSe[1 | 2]:FILTer:STATe <asc> set/return filter state, <asc> = OFF, ON, AUTO

SENSe[1 | 2]:FILTer:TIMe <n> set/return filter time, <n> = 0.01 to 15.00 seconds

SENSe[1 | 2]:IMPEDance <n> set/return voltage probe sensor impedance for power calculations

Table 4-1 Remote Command Summary (Cont)

1 2 ... 127 128 129 130 131 132 133 134 135 136 137 ... 169 170

Comentarios a estos manuales

Sin comentarios

Boonton 4530 Peak Power Meter User Manual Manual de usuario Pagina 132

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos de medición Boonton 4530 Peak Power Meter User Manual